Connector Comparison Test: Comments and Suggestions Please - Page 3
Page 3 of 3 FirstFirst 123
Results 21 to 23 of 23
  1. #21
    Senior Member
    Points: 185,930, Level: 100
    Level completed: 0%, Points required for next Level: 0
    Overall activity: 99.5%
    MtStream's Avatar
    Join Date
    Aug 2014
    Location
    Dallas, TX
    Posts
    2,892
    Glock Armorer?
    Yes
    Glocks Owned
    Many
    Rep Power
    16
    Funny you brought this up, I was thinking about the same thing last night.

    In the past, I removed the roller from my gauge so I just had the bar. I then cut a thin, long strip of masking tape and wound it around the trigger for two reasons

    1) hold the trigger safety down - the movement of the trigger safety made a consistent pull hard.

    2) create a little ledge on the trigger that I would use to keep the gauge in the same spot on the trigger each time.

    I also set the gun upside down on a flat surface and used a wood block to slide the gage along to ensure the angle of the pull was consistent each time.

    This worked fairly well but it was a little tedious to wrap the tape with the trigger in the gun. It also has to be taken off/put back on each time you remove the trigger from the frame (change connectors).

    Last night I was thinking of removing the trigger safety from a spare trigger and using a dremel to cut a notch for the gage to sit it. I was wondering if I could make it wide enough to keep the roller on the gage when I decided to go to bed.

    Something else I’d like to figure out but don’t know how, is to measure the angle on each connector’s ledge.


    Sent from my iPhone using Tapatalk
    I'm on Twitter @GlockGuide http://twitter.com/GlockGuide

  2. #22
    Senior Member
    Points: 769,001, Level: 100
    Level completed: 0%, Points required for next Level: 0
    Overall activity: 99.6%
    Otintx's Avatar
    Join Date
    Oct 2011
    Location
    South of Texas
    Posts
    6,011
    Glock Armorer?
    No
    Glocks Owned
    Several
    Rep Power
    18
    Something else I’d like to figure out but don’t know how, is to measure the angle on each connector’s ledge.
    .....
    Attached Images Attached Images  

    Josey Wales: When I get to likin' someone, they ain't around long.
    Lone Watie: I notice when you get to DISlikin' someone they ain't around for long neither.

  3. #23
    Super Moderator
    Points: 55,396, Level: 100
    Level completed: 0%, Points required for next Level: 0
    Overall activity: 74.0%
    __jb's Avatar
    Join Date
    Jul 2010
    Location
    Sunshine State
    Posts
    6,876
    Glock Armorer?
    Yes
    Glocks Owned
    Help... My Glocks have started multiplying...
    Rep Power
    22
    It's such a small piece... The angle will be difficult to measure.

    I envision aligning the connector vertically over a protractor and then put a straight edge on the angle of the connector... The long straight edge would help get an accurate reading... Maybe build a little jig to hold the connectors consistently.

    Be curious to see how close the angles are... Interesting to see how close the angle is on the same, but different, connectors.
    "While the anti-gunners seem very concerned about the "one life" that your firearm might take -- they are not very concerned about the lives it will save." Jon H. Gutmacher, Florida Firearms - Law, Use & Ownership

Page 3 of 3 FirstFirst 123

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Glock 23 gen 4 review and comparison to gen 3 23
    By Tshark in forum Glock Pistols
    Replies: 9
    Last Post: 06-04-2012, 05:51 PM
  2. Ammo Size Comparison Charts
    By Otintx in forum Ammunition
    Replies: 5
    Last Post: 03-31-2012, 10:56 PM
  3. comparison
    By Marc in forum Glock Pistols
    Replies: 71
    Last Post: 02-08-2011, 05:22 PM
  4. Best Self defense Ammo Comparison.
    By DWinter in forum Ammunition
    Replies: 6
    Last Post: 12-18-2010, 11:43 PM
  5. My first Glock, any suggestions/ comments?
    By jbwood003 in forum Glock Pistols
    Replies: 14
    Last Post: 10-17-2010, 07:42 PM

Search tags for this page

best 3.5 connector for glock
,
glock comparison chart
,

glock connector comparison

,

glock safety trigger

,

glock trigger connector comparison

,
glock trigger pull
,

glock trigger safety

,
lone wolf discount code
,

trigger pull gauge

,
zev tech v4 race connector review